House Dust IPA - Wednesday, Nov. 18, 2026 - ( with CaraRed )


 

I finally got my sink installed. A lot of work from scratch along with the confined space which 
seems to be the biggest hurdle with anything in this house. I have 4 sachets of US-05 so I am
good to go.                  

Thanks Frank, another perfect job!!

Ingredients
9 lbs. Rahr 2 row
2 lbs. Pils Malt
8 ozs. CaraRed
18.70 g Warrior @ 60 min.
56 g Cascade @ 10 min.
56 g Cascade @ 0 min.
28 g Cascade dry hop 3 days before kegging
US-05

I ran out of whirlfloc or it is somewhere else. I did a whirlpool and letting it sit for 30 minutes.
I hope to not get like 3-4 litres of trub in the carboy. It just takes up too much room and I will
be short of wort.

Mash Volume - 5.75 gallons
Sparge Volume - 3 gallons
.1 ml Lactic Acid in sparge
No lactic in mash

Mash
Gyp - 7.6 g
CI - 1.7 g
Eps - 4.4 g

Boil
Gyp - 4 g
CI - .9 g
Eps - 2.3 g

O.G. - 1.043
F.G. - 
% -
SRM - 4
BU - 41

I bought a 1000 watt burner plate to heat sparge water. I can't use it along with Mr. Robobrew
on the same circuit of course, I need to plug in Mr. Robobrew by itself so I am going to plug
it in over by my small beer fridge. If that is an issue, I can unplug it during beer making. What a fucken house this is!!! It is unbelievable to go through so much BS just to make beer. No space
to do anything. At least Mr. Robobrew seems to be at the same temp as my part time thermopen.
I plugged in Mr. Robobrew and added 2 gallons of water, It didn't flip a breaker so I am good
to go. Now I just have to get my mill at a sweet spot that doesn't turn my grain into flour. I think it was a little bit over milled, but thinking of the past batches, if I loosend it up a bit, my efficiency went way down. My burner instructions said not to use an oversized pot. I am using an oversized
pot. Hell, they all are. What size of pot can you use on this thing if not an oversized one? Heating iup a pot now. I may have too much in the pot though. If it isn't enough on brew day, I will just
grab some RO water to top it up. I can add more water to the mash next time if this isn't going
to work out. Too bad I don't have a 20 amp circuit I can use. There is a 20 amp breaker in the
panel but I already bought this so just use it if it seems to hold up okay.

                                                       BREW DAY NOTES

Everything went well today. I need to buy a brass male 3/4" garden hose fitting to replace that thing that came with it. I will however have to cut the hose and get a quick disconnect so I don't have to jam the hose on every brew day. I have one but no idea where the hell it is. Got up at 4:15 AM and got going as soon as I could. A lot of stuff to do and walk around stuff because of the
tight brewing setup. The burner worked good. I shut it off 15 minutes before I needed it and the
temp was okay. I will stick with the 11 L pot even though I did need more but if I let the sparge process go longer I will be up to 7.5 gallons. I got 5 compost bags in the green bin. Not as bad
as I thought. Brew bag in the wash so we will see how clean it gets. At least now I won't have to
worry about what goes in a sump pump.

                                                 MR. ROROBREW AND LOWER BOIL

I don't know the reason for the low boil but I am going to buy a Reflex thingy that people
use to insulate their hot water heaters. A normal brew day as far as time is concerned. I do
have to get used to walking around stuff and I can't leave anything in the beer room that is
not part of the process, no room.

                           DO NOT FORGET TO DRY HOP 3 DAYS BEFORE KEGGING

Day 1 - Pitched yeast @ 5pm. 68F.
Day 2 - Nothing, but that is expected with US-05.




Comments

Popular posts from this blog

Kings Landing IPA - Extract - Monday, October 2nd, 2017

Heritage Estates Chardonnay - Thursday, July 9, 2020

Brew Day - September 1, 2009